收藏本站
LDS8869
selecting the register address and then programming
data into that register.
An internal counter records the number of falling
edges to identify the address and data. The address
is serially programmed adhering to low and high
duration time delays. One down pulse corresponds to
register 1 being selected. Two down pulses
correspond to register 2 being selected and so on up
to register 6. t LO and t HI must be within 200ns to
100 μ s. Any pulse with less than 200 ns width may be
ignored.
Once the final rising edge of the address pulse is
programmed, the user must wait at least 500 μ s
before programming the first data pulse. Any falling
edge after this minimum delay will be recognised as a
first data pulse.
Data in a register is reset once it is selected by the
address pulses. If a register is selected but no data is
programmed, next pulse sequence will be recognized
as data only. Do not send register address only
without following data because it may disrupt normal
device operation.
Once the final rising edge of the data pulses is
programmed, the user must wait at least 1.5ms
before programming another address. If
programming fails or is interrupted, the user must
wait at least 2 ms (t RESETDELAY ) from the last rising
edge before reprogramming can commence.
Upon EN/SET pin goes high the device automatically
starts looking for an address. If no falling edge is
detected within 100 μ s, then the user must wait at
least 2 ms before trying to program the device again.
The device requires a minimum 10 μ s delay to ensure
the initialization of the internal logic at power-up. After
this time delay, EN/SET pin may be set high and the
device registers may be programmed adhering to the
timing constraints shown in Figure 1.
Register REG1 allows to set the mode and select the
pairs of LEDs to be turned on. A low LED current
mode exists to allow for very low current operation
under 4mA per channel. If IMODE equals 1, the high
current range is selected up to 32mA. If IMODE is set
to 0, all currents are divided by 8. Each bank of LEDs
(A, B or C) can be turned on independently by setting
the respective bit ENA, ENB, ENC to 1.
Register REG2 allows to set the same current for all
6 channels. REG3, REG4, REG5 allow to set the
current respectively in banks C, B and A. The three
banks can be programmed with independent current
REG6 contains the return lockout (RTLKO) bit. This
stops the charge pump returning to 1x mode. One
pulse sets it to 1. Two pulses set RTLKO to 0. When
RTLKO is set to 1, the charge pump cannot
automatically return to 1x mode when in one of the
charge pump modes. The device can however move
from 1x to 1.33x, or to 1.5x and 2x if the input voltage
is not sufficient to drive the programmed LED
currents.
REG6 also triggers a charge pump. This forces the
charge pump to start from 1x mode and determine
the correct mode it should be in to drive the LEDs
most efficiently. If the input voltage has risen or the
device has been reprogrammed to other LED values,
it is recommended to trigger this reset allowing the
charge pump to run in the most efficient mode.
To power-down the device and turn-off all current
sources, the EN/SET input should be low for at least
1.5ms (t OFF ) or longer. The driver typically powers-
down with a delay of about 1ms. All register data are
cleared.
Unused LED Channels
For applications with only four or two LEDs, unused
LED banks can be disabled via the enable register
internally and left to float or connect to Vout.
For applications requiring 1, 3, or 5 channels, the
unused LED pins should be tied to V OUT (see Figure
3). If LED pin voltage is within 1 V of V OUT , then the
channel is switched off and a 250 μ A test current is
placed in the channel to sense when the channel
moves below V OUT – 1.5 V.
Protection Modes
The LDS8869 has follow protection modes:
Figure 3. Application circuit with 5 LEDs
1. LED short to V OUT protection
If LED pin is shorted to V OUT , LED burned out
becomes as short circuit, or LED pin voltage is within
values.
? 2009 IXIS Corp.
Characteristics subject to change without notice
10
from V OUT to (V OUT -
1.5V) range, LDS8869
Doc. No. 8869_DS, Rev. N2.1
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
LDV100-012SN POWER SUPPLY LED 90W 12V COMPACT
LDV100-024SN POWER SUPPLY LED 100W 24V COMPAC
LE25S40MB-AH IC MEM 4MBIT SERIAL FLASH 8SOP
LE25U20AMB-AH IC MEM 2MBIT SERIAL FLASH 8SOP
LFDAS12XSIT HARDWARE MC9S12XS 112-PIN
LFXP10E-L-EV BOARD EVAL LATTICEXP10E STD
LH28F008SCHT-TE IC FLASH 8MBIT 85NS 40TSOP
LH28F160S3HNS-TV IC FLASH 16MBIT 100NS 56SSOP
相关代理商/技术参数
LDS9003-002-T2 功能描述:LED照明驱动器 High Power LED Temp & PWM Contr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
LDS-A2802RI 功能描述:LED 显示器和配件 .28" Sng Digit Disp 565nm Green LEDs RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube
LDS-A2802RI-SUG 功能描述:LED 显示器和配件 .28" Sng Digit Disp 574nm Green LEDs RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube
LDS-A2804RI 功能描述:LED 显示器和配件 .28" Sng Digit Disp 635nm Red LEDs RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube
LDS-A2804RI-750 功能描述:LED 显示器和配件 LED Display RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube
LDS-A301BE 功能描述:LED 显示器和配件 LED Display RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube
LDS-A301BI 功能描述:LED 显示器和配件 LED Display RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube
LDS-A301LE 功能描述:LED 显示器和配件 LED Display RoHS:否 制造商:Avago Technologies 显示器类型:7 Segment 数位数量:2 字符大小:7.8 mm x 14.22 mm 照明颜色:Red 波长:628 nm 共用管脚:Common Anode 工作电压:2.05 V 工作电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 35 C 封装:Tube